Safety is the key - this preparation is what counts
Occupational safety is a top priority when you sharpen a lawnmower knife yourself. It must be ensured that the mower cannot start up. You should exercise this caution in all work relating to the maintenance of a lawnmower. This is how you do it:
- Pull the spark plug connector on the petrol-powered mower
- On the electric lawn mower, pull the cable out of the power plug
- Remove the battery from a cordless mower
also read
- Change lawn mower blades yourself - step-by-step instructions
- Processing of tomatoes - explained step by step
- Build a privacy fence out of wood yourself - step-by-step instructions
In addition, sturdy work gloves and protective clothing are mandatory. Ideally, wear long-sleeved clothing, long trousers, sturdy shoes and protective goggles.
Material and tool requirements
If all work materials and tools are ready to hand, sharpening the lawnmower blades is quick and easy. This is how you should be equipped:
- Open-end wrench or adjustable wrench
- Allen key
- Pipe wrench
- Workshop quality files
- Grindstone, e.g. B. Scythe whetstone
- vice
- Rubber mallet
- Operating instructions for the lawn mower
How to remove the lawnmower blade
Turn the mower over so you can access the lawn mower blade. Position a petrol mower so that the air filter is at its highest point. In this way, most models will not leak gas from the tank. Now take the operating instructions for the lawn mower to hand in order to then remove the cutter bar.
If the operating instructions are lost, this does not prevent you from continuing work. Use the combination or combination wrench to loosen the retaining screw in the middle. Shape Make sure that any washers are properly seated.
Tips
A lawnmower blade on a petrol lawnmower should never be sharpened while it is installed. The risk of flying sparks igniting spilled gasoline is far too great. It is safer to remove the cutter bar so that it can be sharpened at a distance from the mower.
Manual sharpening tops the grinding machine - this is how it works
The removed lawnmower blade is fixed in a vice, which simplifies all of the following work steps. Proceed in these steps:
- Use the file to grind the lawnmower blade from the outside to the inside
- In the second stage, rework the knife edge with the whetstone
- Completely remove the remaining burr so that it does not fold over later and the knife becomes blunt again
Experts do not recommend sanding a lawnmower blade with a flex. The knife is heated excessively, which results in a rough finish. In addition, the removal increases unnecessarily, which can cause a greater imbalance. This is only corrected by a corresponding material acceptance on the other side.
What to do if you sanded from the wrong side?
In the heat of the moment, inexperienced hobby gardeners sometimes grind a lawnmower blade from the wrong side. If the quality of the lawn suffers as a result, the knife should be sharpened immediately. Unfortunately, this is done at the expense of a relatively large amount of material on the blade.
As long as the quality of the cut on the grass is acceptable, the lawnmower blade is machined from the right side step by step with each further sanding. In this way, the correct cutting angle gradually moves to the desired side. Here, the angle should first be set a little flatter, as long as both sides of the knife are still sharp. If the bevel on the wrong side has disappeared due to wear, increase the angle on the right side again.
Protecting the lawnmower blade from unbalance - how it works
If you do not sharpen a lawnmower blade to the same extent on both sides, the cutter bar will later swing back and forth more or less uncontrollably due to an imbalance in the mower. You can prevent this situation in the following way:
- Drive a nail horizontally into a sturdy piece of wood
- Hang the cutter bar on its central hole
- If one side tilts down, there is an imbalance
- Sand the heavier side of the lawn mower blade again
Ideally, you should use this method to check the balance on the lawnmower blade in between and at the end of the grinding work. Only when the cutter bar is perfectly balanced is it reinstalled in the mower. Otherwise the engine block could be damaged and a simple sanding process results in a comprehensive lawnmower repair.
How often do lawnmower blades need to be sharpened?
The level of use largely determines how often a lawnmower blade needs to be sharpened. If the knives often hit branches and stones, they dull faster. As a rule, a single sanding per season is enough to perfect a lawn mowing. If you take a look at the lawnmower blade regularly, you don't have to worry about frayed grass.
Tips & Tricks
To grow a perfect English lawn, a cylinder mower is essential. Unfortunately, its construction resists any attempt to sharpen the knives manually. Special grinding machines for cylinder mowers, however, cost more than 2,000 euros, so that such an investment will not be worthwhile until the second Or 3. Generation of gardeners amortized.
